itbrainpower.net
BMP280 ** temperature, pressure ** I2C environmental sensor



Read our last post: Modems and RaspberryPI 5. RaspberryPI OS [Debian 12 bookworm] notes.. Order u-GSM modems.

BMP280 breakout :: FEATURES


BMP280 sensor breakout - topBMP280 sensor breakout - bottom


PN: SS-BMP280#I2C   SKU: ITBP-6001

BMP280 (manufactured by Bosch Sensortec) is a combined digital sensor with with temperature and pressure measurement based on proven sensing principles and having low power consumption.
- ambient range for operation -40 ~ +85C, 0%-100% r.H., 300-1100hPa
- absolute temperature (0-65C) accuracy +-1C
- absolute pressure accuracy max. +-1.7hPa
BMP280 datasheet

BMP280 breakout features:
* input voltages between 3.3-5V
* I2C interface, 3.3-5V auto [default I2C voltage follows the Vin powering voltage]
* I2C voltage option via solder jumper [Eg.: power at 5V and I2C at 3.3V; power and I2C at 2.2V]
* alternative sensor I2C addresses via solder jumpers
* compatible with Arduino (all), Raspberry PI (all) and other SBC / MCU
* Arduino C, Raspberry PI [Python] software support
* compatible with xyz-mIoT boards(Arduino Zero like)
* big soldering pads on 2.54 mm [0.1"] pitch for standard row header / connector

* 13x27mm, around 2grams
 

BMP280 breakout :: INTERFACES, PADS and SOLDER JUMPERS

s-Sense BMP280 sensor breakout top - pinout description

I2C and POWERING INTERFACE

In the left edge of the top PCB side, top to bottom:
1. Vin - POWER IN 3.3V / 5V (default) *
2. 3V3 - Vdd - LDO output (default) / LDO bypass IN **
3. SDA - I2C SDA [default, pulled up at Vin]***
4. SCL - I2C SCL [default, pullup up at Vin]***
5. GND - POWER and I2C GROUND
 * Default, the I2C reference voltage follow the Vin voltage. If your board (Arduino/other) it's 5V compliant, connect +5V to Vin. Similar, for 3.3V compliant board(RPI/Arduino)connect 3.3V source to Vin.
** 3.3V voltage it's available on Vdd PAD, if Vin it's connected to 5V. Bypass LDO - see schema and read docs.
*** Default, the I2C reference voltage follows the Vin voltage! Read bellow about I2C reference voltage and s1 solder jumper.

SOLDER JUMPERS

s1 : I2C reference [Vin or 3V3-bypass], default Vin *
s2 : RESERVED
s3 : BMP280 I2C address [0x76/0x77], default 0x76 *
* Read about s1 and s3 functionality bellow.

s-Sense BMP280 sensor breakout bottom - pinout description

SIGNALS INTERFACE and MARKING

In the left edge of the bottom PCB side, top to bottom:
6. RESERVED
7. RESERVED
8. RESERVED
9. RESERVED
 nc. NOT CONNECTED
 * Taking a look at howto posts and inside software examples may be quite helpful.

 Observe the sensor breakout marking on PCB board (here, BMP280 sensor it's marked as populated).

 

BMP280 breakout :: Arduino / Raspberry PI basic interfacing
BMP280 breakout Arduino 5V [Eg.: UNO] Arduino 3.3V [Eg.: Zero] RPI [B/B+/II/3/3+/Zero/Zero W]
Vin PAD* 5V 3.3V PIN1 (3.3V)
Vdd PAD (3V3)* - - -
SDA PAD SDA SDA PIN3 (SDA)
SCL PAD SCL SCL PIN5 (SCL)
GND PAD GND GND PIN9 (GND)
 
* here, power in default mode (sensor & MCU power and I2C at same voltage!!). For alternate mode see solder jumper description bellow.
 
 

BMP280 breakout :: solder jumpers description; power scenarios


s1* - I2C reference voltage selector - shipped with circuit 1-2 closed and circuit 2-3 open (default mode).

In default mode, the I2C reference voltage follows the voltage applied to Vin! Default mode use cases:
      - shield/MCU it's 5V compatible ==> connect Vin at 5V; the I2C reference it's 5V!
      - SBC/shield/MCU it's 3.3V compatible ==>connect Vin at 3.3V; the I2C reference it's 3.3V!.

Alternate mode - I2C reference voltage follows the Vdd voltage! - modify s1 as: 1-2 circuit open, 2-3 circuit closed [carefully interrupt/cut the circuit line between pads 1 and 2, and solder over pads 2 and 3].

Alternate mode scenarios:
      - apply 3.6-7V to Vin. The I2C reference voltage it's set at 3.3V! Also, at Vdd pad (LDO output) 3.3V (up to 100mA) it's available for third part powering (anyway, try to keep the sunk current as low as possible, in order to avoid thermal errors).
      - keep Vin not connected. Apply 2.8 or 3.3V to Vdd (the LDO it's bypassed). The I2C reference voltage it's set at voltage applied to Vdd pad!

s3 - BME I2C address - default circuit open, BMP280 having 0x76 as I2C address. Solder over s3 pads [circuit closed] in order to select the alternate I2C address [0x77].

* Consult s-Sense block schema for more information. See projects/how to section.

BMP280 breakout :: ARDUINO & RaspberryPI software 

s-Sense air quality and environmental sensors examples for Arduino and RaspberryPI may be downloaded from our download page.


BMP280 breakout :: DOCUMENTATION DOWNLOAD/ONLINE

The s-Sense environmental sensors documentation can be found here.


BMP280 breakout :: ARDUINO & RaspberryPI projects

Arduino & RaspberryPI projects based on itbrainpower.net products

 

BMP280 breakout :: ORDER ONLINE

Order online s-Sense air quality and environmental sensor breakout boards
 

BMP280 breakout :: ORDER FROM OUR DISTRIBUTORS

Choose and order from one distributor near you.



View/save pdf version of this page.


 
 
 
 
 
 
document version 0.9142 / 2020-08-07 © R&D Software Solutions srl