itbrainpower.net

xyz-mIoT equipped w. BG96 modem ** low power ARM0 IoT shield with
LTE CATM1, NBIOT, eGPRS modem + GNSS and optional sensors



BLACK FRIDAY SALE! Order here: LTE modems (u-GSM), IoT shields w. LTE modems (xyz-mIoT) and sensors (s-Sense).

xyz-mIoT equipped with BG96 modem :: FEATURES


xyz-mIoT equipped with BG96 modem - low power ARM0 IoT shield with LTE CATM1, NBIOT, eGPRS modem + GNSS and optional sensors - top xyz-mIoT equipped with BG96 modem - low power ARM0 IoT shield with LTE CATM1, NBIOT, eGPRS modem + GNSS and optional sensors - bottom


PN: XYZMIOT209#BG96-UFL-1100000   SKU: ITBP-4002 - LiPO charger, HDC2010 (THS) and DRV5032 (HALL), uFL
PN: XYZMIOT209#BG96-UFL-0000000   SKU: ITBP-4003 - LiPO charger, no embedded sensors, uFL
PN: XYZMIOT209#BG96-SMA-0000000   SKU: ITBP-4053 - LiPO charger, no embedded sensors, SMA
PN: XYZMIOT209#BG96-UFL-ULP   SKU: ITBP-4073 - ultra low power (~7-9 uA deep sleep), Lithium Primer battery only, no embedded sensors, uFL
PN: XYZMIOT209#BG96-SMA-ULP   SKU: ITBP-4083 - ultra low power (~7-9 uA deep sleep), Lithium Primer battery only, no embedded sensors, SMA
Above devices have GLOBAL coverage for LTE CATM1 and NB IoT and GSM(2G) networks!

other modem variants: xyz-mIoT equipped w. M95FA modem [GSM / GPRS], xyz-mIoT equipped w. BG95 modem [LTE CATM / NB IoT + GNSS], xyz-mIoT equipped w. BC95G modem [NBIOT], xyz-mIoT equipped w. EG91E modem [LTE CAT1 / 3G / GSM], xyz-mIoT equipped w. EG95A modem [LTE CAT4 / 3G + GNSS] and xyz-mIoT basic [no modem]


Modem side - Quectel BG96
Radio protocols: LTE CATM1 + NB IoT + EGPRS
GLOBAL coverage: yes - see bands and transfer speeds supported here.
GNSS support: yes - multi constellation - GPS, GLONASS, BeiDou/Compass, Galileo and QZSS
SIM support: 1 x NANO SIM/USIM socket.
External SIM support: yes - 5 pin 1.27mm interface.
Embedded SIM support: yes - feature available for high volume batches and for selected partners only

Additional power management: modem power separation controlled by shield MCU
GNSS active antenna: yes + power management by shield MCU

GSM radio interface: u.FL (SKU: ITBP-4001, ITBP-4002, ITBP-4003 and ITBP-4073) or SMA (SKU: ITBP-4053 and ITBP-4083)
GNSS radio interface: u.FL

modem USB soldering pads: yes

Quectel BG96 modem specifications (pdf)
Quectel BG96 AT commands (pdf)

MCU side - ATMEL SAMD21G - Arm® Cortex®-M0 32-bit.
Clock Speed: 32.768 kHz (RTCC) - crystal controlled, 48 MHz
Flash Memory / SRAM: 256 KB / 32KB
WDT: yes, having crystal time accuracy support

Interfacing Voltage: 3.3V
Digital I/O Pins:13 + (analog, I2C, SPI, other) pins via alternate function + 2 reserved for shield power management
DC current per I/O Pin: 7 mA
PWM Pins: 12
UART (hardware): 1 + 1 reserved for modem communication
SPI(hardware) 1
I2C (hardware) 1
Analog Input Pins 5 (ADC 8/10/12 bit)
External Interrupts 8

Microchip/Atmel ATSAMD21G - ARM0 microcontroller datasheet (pdf)

Embedded sensors side
optional sensors: up to six sensors, PN dependent - see sensors per PN here
THS sensor (optional): HDC2010 - Low Power Humidity and Temperature Digital Sensor datasheet (pdf)
CO2 + TVOC sensor (optional): CCS811 - Ultra-Low Power Digital Gas Sensor for Monitoring Indoor Air Quality datasheet (pdf)
HALL sensor (optional): DRV5032 - Ultra-Low-Power Digital-Switch Hall Effect Sensor datasheet (pdf)
IR sensor (optional): KP-2012P3C - IR phototransistor datasheet (pdf)
vibration / tilt sensor (optional): SW-200D - roll ball switch datasheet (pdf)

voltage samplers (standard) - 2 dedicated ADCs for Vraw (power in line) and Vbat (battery voltage)

Powering side and power management
Specifications for ITBP-4073 and ITBP-4083 ultra low power variants:
Ultra low power design: yes – down to 7-9uA* total shield deep sleep current support
Direct powering: - 3.00-3.68 V supply (min. 500mA sustained and 2A pulse capable) applied to VBAT and GND pins.
Integrated battery charger: no
Rechargeable batteries support: no

Specifications for ITBP-4001, ITBP-4002, ITBP-4003 and ITBP-4053 variants
Low power design: yes – down to 35-40uA* total shield deep sleep current support
No rechargeable battery powering: yes - 3.60-4.20 V supply (min. 500mA sustained and 2A pulse capable) connected to VBAT and GND pins.
Integrated battery charger: yes having 6V solar cell support
Rechargeable batteries supported: single cell LiPO / LiION min. 250mAh or super-capacitor >1F / >5V w. ESR less than 150mOhm
Battery charger inputs and voltages: USB (5V) / Vraw (4.8-7V)

Specifications common for all variants:
Lithium primer battery support : yes - via VBAT and GND pins.

3.3V for MCU, sensors and external devices: via internal LDO

max. current on 3.3V PAD: 75mA minus the total current sink by output ports
max. DC current per MCU I/O pin: 7 mA

Additional modem power management: yes(modem power separation controlled by MCU
GNSS active antenna power management: yes(enable / disable GNSS antenna power controlled by MCU)
* measured at 25 C, RTCC and GPIO interrupt wake routines, crystal controlled WDT and RTCC, two UART and I2C. No embedded sensors variant was used for this test.

Mechanical
Dimensions: 1.4"x1.8" (35.56 x 45.72mm).
Weight: ~7g.

 
 
 

xyz-mIoT equipped with BG96 modem :: INTERFACES, PADS / PORTS and CONNECTORS

xyz-mIoT shield v 2.09 - bottom layer, component identification

PADS / PORTS


Right image: bottom PCB with component identification.

PADS & PORTS allocation information here.
More accurate info should be obtain by consulting xyz-mIoT block schema.

Keep in mind that available components and features are PN dependent, check this.
 

xyz-mIoT shield v 2.09 equipped with BG96 modem - bottom layer, LEDs and RESET SWITCH

LEDs, RESET SWITCH and additional info


1. RESET SWITCH - RESET/PROGRAMMING functions*
2. GREEN LED - network status LED
3. YELLOW LED - D13 - ARDUINO system LED
4. RED LED (left) - battery charger LED
5. RED LED (center) - modem power LED

* enable programming mode - push RESET twice (fast)
* reset shield - push RESET button only once

- on right side - nano SIM socket connector
- on left side - LiPO battery PADS (LiPO+/Vbat and GND)
- on left side - USB mini B connector

 

xyz-mIoT shield v 2.09 equipped with BG96 modem - external SIM  interface and GSM connector

External SIM CARD port, antenna connector


External SIM card interface
1. SIM VDD
2. SIM DATA
3. SIM RESET
4. SIM GND
5. SIM CLOCK
- if not used, leave them not connected
- if used, in order to avoid interferences, keep the wires as short as possible and take in to account the routing.


GSM side antenna connector
xyz-mIoT shield may be ordered with u.FL connector or with SMA F connector. Check PN and options here.


 
 

xyz-mIoT equipped with BG96 modem :: ARDUINO libraries, EXAMPLES and UTILITIES 

Resources marked with "#", requires for download the following information: your name, email address and the modem IMEI. The modem IMEI can be found printed on the Quectel GSM module, or run AT+GMGS command.

xyz-mIoT shield Arduino board definition library, RTCC, WDT and low power Arduino support libraries, embedded sensors Arduino libraries and code examples for Arduino can be downloaded from our download page.


xyz-mIoT equipped with BG96 modem :: DOCUMENTATION DOWNLOAD/ONLINE

The xyz-mIoT shield documentation can be found here.


xyz-mIoT equipped with BG96 modem :: ARDUINO PROJECTS

GETTING STARTED posts containing xyz-mIoT by itbrainpower.net powering, low power / solar cell powering tips and tricks and interfacing guidelines for GSM / low power modems, ethernet, WIFI, LORA, SD card reader, TFT displays, sensors, relays and other modules, together with CLOUD integration examples can be found in projects section.

 

xyz-mIoT equipped with BG96 modem :: ORDER ONLINE

Variants having onboard LiPO/LiION battery charger and embedded sensors:
- xyz-mIoT w. BG96, HDC2010(THS), DRV5032(HALL) and uFL connector >> ITBP-4002

Variants having onboard LiPO/LiION battery charger, no sensors embedded:
- xyz-mIoT w. BG96 and uFL connector >> ITBP-4003
- xyz-mIoT w. BG96 and SMA connector >> ITBP-4053

Ultra low power variants (for lithium primer batteries only), no sensors embedded:
- xyz-mIoT w. BG96 and uFL connector >> ITBP-4073
- xyz-mIoT w. BG96 and SMA connector >> ITBP-4083


 

xyz-mIoT equipped with BG96 modem :: ORDER FROM OUR DISTRIBUTORS

Choose and order from one distributor near you.

 
 

This resource is under UPDATE...

 
 
 
 
document version 1.222 / 2022-02-10 © R&D Software Solutions srl